Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WM8 UN - PA6-MD40 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Propiedades específicas del material - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

40 % mineral reinforced polyamide 6 injection moulding compound. It possesses high stiffness, dimensional stability and heat resistance combined with excellent processability as well as low warp and resistance to sink-mark formation. It is ideally suited for applications such as chrome platable door handles and fuel filler lids.

Caracteristicas de procesamiento y fisicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Indice de fluidez volumétrico, MVR	45 / *	cm³/10min	ISO 1133
Temperatura	275 / *	°C	-
Carga	5 / *	kg	-
Contracción posterior al moldeo, paralelo	1.0 / *	%	ISO 294-4, 2577
Contracción posterior al moldeo, normal	0.9 / *	%	ISO 294-4, 2577

Propiedades mecánicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Módulo de tracción	6000 / 2000	MPa	ISO 527
Resistencia a la tracción	85 / 45	MPa	ISO 527
Alargamiento a rotura	11 / 40	%	ISO 527
Resistencia al impacto Charpy, +23°C	180 / 220	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy, -30°C	120 / 110	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C	5 / 10	kJ/m²	ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C	4 / 3.5	kJ/m²	ISO 179/1eA

Propiedades térmicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	220 / *	°C	ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa	100 / *	°C	ISO 75-1/-2
Estabilidad al calor, 0.45 MPa	190 / *	°C	ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo	57 / *	E-6/K	ISO 11359-1/-2
Coef.de expansión térmica lineal, normal	65 / *	E-6/K	ISO 11359-1/-2

Otras propiedades	Seco / Cond	Unidades	Método de ensayo
Densidad	1490 / -	kg/m³	ISO 1183

Propiedades específicas del material	Seco / Cond	Unidades	Método de ensayo
ISO Data
Indice de viscosidad	145 / *	cm³/g	ISO 307, 1157, 1628

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección

Forma de suministro

Sémola, Color natural

Aditivos

Desmoldeante

Disponibilidad regional

Norteamérica, Europa

Demás información

Moldeo por inyección

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 270 - 300 °C
injection molding, Mold temperature, range: 80 - 95 °C
injection molding, Mold temperature, recommended: 80 °C
injection molding, Dwell time, thermoplastics: 10 min

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.